Repairable Phone: The Engineering Behind a Phone You Can Open
A phone that can be repaired is designed differently, not just opened differently. Learn the five design decisions that make the difference.
The five decisions that make a phone repairable
First, the battery comes out without destroying anything. On most phones the battery is glued down with a strong adhesive that has to be dissolved with solvent, and that solvent often leaves the phone unusable. A repairable phone uses a pull tab or a captive screw, so a worn battery is a two-minute job with no risk to the screen.
Second, screws and clips instead of adhesive. Adhesive is cheaper and thinner, and it makes the device feel solid. It also makes any single component failure a reason to replace the whole device. Third, modules connect with standard board-to-board connectors rather than being soldered, so a camera can be unplugged instead of desoldered. Fourth, the spare parts are actually sold, at a price a person can afford, and the software keeps working afterwards. A phone whose replacement parts are unavailable or whose updates stop in two years is not repairable in any meaningful sense. Fifth, the whole design has to accept the consequences, and here is the honest part: connectors take space, screws take thickness, and a modular device is usually thicker and heavier than a glued one.
What that looks like in a real modular phone
The Fairphone 5 is the clearest example on the market. It measures 161.6 by 75.8 by 9.6 mm, weighs 212 g, and lists ten user-replaceable spare parts, including the wide camera, the ultrawide camera, the selfie camera, the USB-C port, the mid-frame, the speakers and the vibration motor. The battery is a 4200 mAh removable cell with a 30 W charger, and the plastic back unclips rather than being glued.
The engineering behind a modular camera is more interesting than it looks. The camera module is not just a lens and a sensor, it is a sensor, an actuator for autofocus and image stabilisation, and a small processor, all connected over a high-speed board-to-board connector that has to carry power, data and control signals without adding much thickness. That is why the module costs real money, and why the company publishes specifications such as the battery's internal impedance rather than pretending the parts are generic. The software story is part of the hardware story. The Fairphone 5 runs a Qualcomm QCM6490, a business and industrial part rather than a consumer flagship chip, chosen for its long support lifetime, and the company commits to software updates until 2031. That decision is a hardware decision about which silicon to buy, and it is arguably the single most effective thing a manufacturer can do for repairability.
Step by step
-
Compare a teardown of two phones
Look at how each one is put together and count the adhesive joints and the screw types. The difference is visible in the first minute.
-
Read a spare parts price list
Look up the cost of a battery, a screen and a camera for a phone you own. Compare each part with the price of a new phone.
-
Measure a battery's internal resistance
Measure a cell's voltage drop under a known load. This is why a battery that feels fine can still make a phone die under load.
-
Build a battery-powered sensor node
Use the deep sleep project on a protected cell and measure the current. It teaches the power budget that a phone engineer reasons about every day.
-
Design a module with a connector
Split a circuit across two boards joined by a connector, and work out what the connector has to carry. It makes the cost of a modular design visible.
-
Plan for the part you can still buy in five years
Choose one device you own and find its parts and its update promise. If neither exists, that is the lesson about longevity.
What you'll need
| Item | Qty | Why |
|---|---|---|
| Protected 18650 cell in a holder | 1 | The cheapest way to experience a battery you can actually replace, and to build a safe power budget. |
| Arduino Nano | 1 | A small controller that runs from the same cell, which is how you learn what a phone is really doing with its power. |
| TP4056 lithium charging module with protection | 1 | Charges a bare cell safely, and its protection circuit is a good lesson in why phones have fuel gauges. |
| DHT22 temperature and humidity sensor | 1 | A representative sensor module, and a good test of whether a connector survives being unplugged and replugged. |
| Small strip of headers and jumper wires | 1 set | Stands in for the board-to-board connectors that make a modular phone modular. |
| Digital caliper | 1 | For measuring connector pitch and battery thickness, the physical limits that decide whether a device can be made modular. |
Practise it before you build it
Every step above has a matching circuit in the ThinkEdge Learn simulator. The simulator runs a real
Arduino sketch against a modified-nodal-analysis solver, so digitalWrite actually drives the
LED on screen and the readings change when you change the wiring — no hardware, no burnt components.
The classic first Arduino project — blink the built-in LED on pin 13 — but done the RIGHT way. Most beginners use delay(1000) to make the LED blink, but delay() blocks the whole CPU so you can't do anything else while the LED blinks. The real Arduino idiom is to track time with millis() and only toggle the LED when enough time has passed. This is how every non-trivial Arduino sketch works.
A common real-world control system: read a sensor, compare to a threshold, switch an output on or off. Air conditioners, heaters, fans, and sprinklers all work this way. The DHT11 reads the room temperature, and a small 5V fan turns on at 30 °C or hotter and off at 27 °C or cooler — the same pattern that runs every thermostat on Earth. The 3 °C gap between the on- and off-thresholds (called hysteresis) stops it from flickering on/off every second when the temperature hovers right around 30 °C.
Real smart fans use TWO sensors: temperature (to know WHEN to turn on) and motion or distance (to know IF someone is present). If it's hot AND someone is within 100 cm, the fan turns on. This avoids the silly situation of a fan blowing in an empty room. We use the DHT11 for temperature, the ultrasonic for distance, and a real DC fan motor for the output.
The Mega has 4 hardware serial ports (Serial, Serial1, Serial2, Serial3). That means you can talk to 4 different devices at the SAME time — like a GPS, a Bluetooth module, an XBee radio, and the USB. Use 3 of those ports to read 3 different sensors in parallel and stream their data to the Serial Monitor as a CSV row every second. This is the foundation of every real Arduino data logger.
The DHT11 is a small blue module that measures temperature (0-50°C) and humidity (20-90%). Inside it has a tiny microcontroller, a humidity sensor, and a thermistor. It speaks a custom one-wire protocol that the Adafruit DHT library decodes for you. You just call dht.readTemperature() and you get a number back.
Common questions
Is a repairable phone worse than a normal phone?
In three measurable ways: it is usually thicker and heavier, because connectors and screws take space; the chipset is often a business part chosen for longevity rather than peak performance; and the price is often higher for the same storage. What you get in return is a battery you can replace in a minute, cameras you can replace individually, and a manufacturer commitment to software updates until 2031.
How much does a fairphone repair cost?
A replacement battery for the Fairphone 5 is around 40 euros, and the company sells ten separate spare parts, including each camera module and the USB-C port. For comparison, a typical screen replacement on a sealed flagship phone can run from 100 to 250 dollars once labour is included, and a camera module is often only repairable as part of a whole new mainboard.
What can a class actually do with this topic?
More than a discussion. Build a two-board device joined by a connector, swap the sensor board to change what it measures, and cost the design including the extra connector. Add a battery that can be removed and charged separately, and students have modelled the real engineering decisions behind repairability in about two sessions.
Related guides
Try the full simulator with your class
103 guided circuit projects, 21 lessons and an in-browser Arduino simulator. The first 15 projects are free, no account needed. NCERT Science mapping on 47 projects, with Arabic and English copy in the regional builds.