Flipper One and Sub-GHz Radio: What the Hardware Is Doing
A radio tool is a transmitter, a receiver and a small screen showing you what went over the air. Learn that hardware and the legality becomes obvious.
What the Flipper One actually is
The Flipper One is a handheld multi-tool built around two processors. A Rockchip RK3576 with eight ARM Cortex-A72 and Cortex-A53 cores runs a full Linux system, with 8 GB of RAM and 64 GB of storage, and handles networking, USB and the M.2 expansion slot. A separate Raspberry Pi RP2350 microcontroller drives the 256 by 144 display, the buttons, the status LEDs and the power subsystem, so the device stays usable even when the Linux side has not finished booting.
The design deliberately separates the two jobs, and it is a good architecture to study. A microcontroller gives deterministic timing and low power for the controls, and a Linux system gives you a package manager, scripting and network tools for everything else. The battery is a 24 Wh pack of about 7000 mAh, and Flipper's own documentation notes that specifications were still being finalised during development, so treat published numbers as subject to change. One point catches people out. The Flipper One does not have a sub-GHz radio, NFC, RFID or infrared built in. Those moved to optional plug-in modules that fit the M.2 Key-B expansion slot under the back plate, which is exactly where an SDR radio or a sub-GHz module goes. The earlier Flipper Zero, by contrast, had the sub-GHz radio built in, and that difference is the single biggest thing to understand when comparing the two devices.
The radio engineering behind a sub-GHz remote
Sub-GHz means below 1 GHz, in the licence-free industrial bands at 315, 433, 868 and 915 MHz. The modulation is simple on purpose. On-off keying literally switches the carrier on and off, and a receiver detects whether the carrier is present in each bit period. Frequency shift keying instead nudges the carrier slightly up or down, which is more resistant to noise. Neither is sophisticated, and that is the point: a cheap transmitter and a cheap receiver can agree on a format without a shared clock. The antenna is where most of the range comes from. A whip antenna is a quarter of a wavelength long, which is about 17 cm at 433 MHz and about 8.6 cm at 868 MHz. At that length the antenna is resonant, meaning it radiates efficiently instead of absorbing the power. A mismatched antenna can throw away most of your transmit power before the signal leaves the room.
The security question comes down to the code. Fixed-code remotes send the same number every time, so one capture can be replayed forever. Rolling-code systems change the number on every press using a synchronised counter, so a captured message is useless later. Most cheap garage remotes and doorbells use rolling codes for exactly that reason. And the radio itself is governed by rules: Europe allows a 1 percent duty cycle and 10 mW ERP on the 868 MHz band, while the Indian 865 to 867 MHz band, which is where LoRaWAN also lives, carries no such duty-cycle limit at the physical layer. The USB side has its own lesson. A USB device tells the host what it is through descriptors, and the host largely believes it. That is why a device which presents itself as a keyboard can type, and why the security community has built entire tools around that behaviour. Understanding it defensively is the point: know what your computer does with a new peripheral, and prefer a setup where unknown devices are blocked by policy rather than by luck.
Step by step
-
Learn to read the spectrum
Watch a remote control's carrier on an inexpensive spectrum display or an RTL-SDR dongle. Seeing 433 MHz appear when you press a button makes the physics concrete.
-
Measure an antenna
Compare the transmit distance with the supplied antenna and with a correctly sized quarter-wave wire. The difference is usually larger than any change to the code.
-
Capture and decode a fixed-code signal
Record the on and off timings of a fixed-code remote and draw the waveform. Timing is the entire encoding, and drawing it explains why the receiver knows where each bit starts.
-
Compare a fixed code with a rolling code
Capture two presses of a modern remote and show that the numbers differ. This is the whole idea behind replay protection, explained in one exercise.
-
Check the legal limits before transmitting
Work out the band, the power and the duty cycle for your country before you transmit anything, and keep the transmissions short.
-
Study USB enumeration on your own machine
Connect a device that presents as a keyboard to your own laptop and watch what the operating system logs. It is the clearest explanation of the USB trust problem you will find.
What you'll need
| Item | Qty | Why |
|---|---|---|
| Flipper One | 1 | The current-generation device, with an RP2350 microcontroller alongside a Linux processor and an M.2 expansion slot. |
| Flipper Zero | 1 | The previous generation, which has the sub-GHz radio built in, so you can compare the two architectures directly. |
| Sub-GHz radio module for the M.2 slot | 1 | The Flipper One has no built-in sub-GHz radio, so the module is what puts that band on the device. |
| 433 MHz quarter-wave antenna | 2 | A correctly resonant antenna is worth more than any change to the transmit code. |
| RTL-SDR dongle | 1 | Receives on many bands at once and is the cheapest way to see what a remote is actually sending. |
| USB-C data cable and a USB data block | 1 each | For the enumeration exercise and for the habit of testing peripherals on a machine you do not mind losing. |
Practise it before you build it
Every step above has a matching circuit in the ThinkEdge Learn simulator. The simulator runs a real
Arduino sketch against a modified-nodal-analysis solver, so digitalWrite actually drives the
LED on screen and the readings change when you change the wiring — no hardware, no burnt components.
The Mega has 4 hardware serial ports (Serial, Serial1, Serial2, Serial3). That means you can talk to 4 different devices at the SAME time — like a GPS, a Bluetooth module, an XBee radio, and the USB. Use 3 of those ports to read 3 different sensors in parallel and stream their data to the Serial Monitor as a CSV row every second. This is the foundation of every real Arduino data logger.
In 1837, Samuel Morse and Alfred Vail invented a way to send messages down a wire using just clicks — short (·) and long (—) signals. Each letter has its own pattern (S = ···, O = ---, SOS = ··· --- ···). Your telegraph has a button (the "key"), a buzzer (the "receiver"), and an LED (so you can see the signal too). Press the button to send a message in Morse code.
A VU (Volume Unit) meter is the bouncing bar of lights you see on old stereos. It works by mapping a sound level to a number of LEDs: quiet = 1 LED, loud = all 5. We will use analogRead() on the sound sensor (some modules have an analog pin too) to get a value from 0-100, then light up LEDs based on that value.
A real Arduino project almost always involves a sensor + a way to see the data. The DHT11 reads temperature and humidity, and the Serial Monitor (the window in the Arduino IDE) shows the readings. The Nano is perfect for this because it plugs directly into a breadboard with no extra wiring for power — you can build a complete data logger in 5 minutes.
Every computer ever built stores numbers the same way: as ON or OFF, called 1 and 0. Four bits give you sixteen different numbers, because each LED can be in one of two states — 2 x 2 x 2 x 2 = 16. Each LED is worth a different amount: the first is worth 1, the next 2, then 4, then 8. Add them up and you get any number from 0 to 15. This project wires four LEDs as those four bits and lights the right ones as you count.
Common questions
Is it legal to transmit on sub-GHz frequencies?
It is legal within the rules of the band you are on, and the rules differ by country. The European 868 MHz band limits power to 10 mW ERP and the duty cycle to 1 percent. The Indian 865 to 867 MHz band, which is where LoRaWAN also operates, has no physical duty-cycle limit but is still licensed for specific uses. Check your national allocation before transmitting, and keep test transmissions short.
What is the difference between the Flipper One and the Flipper Zero?
The Flipper Zero is a microcontroller-based handheld with a built-in sub-GHz radio and a monochrome display. The Flipper One is a much larger dual-processor device that runs Linux, has a bigger monochrome screen, two Gigabit Ethernet ports and Wi-Fi 6E, and an M.2 slot for expansion. Because of regulatory and design choices, the sub-GHz, NFC, RFID and infrared radios are optional modules on the Flipper One rather than built in.
Is it safe to plug an unknown USB device into a school laptop?
Not without a policy in place. A USB device can present itself as a keyboard, and the host usually believes the description it is given. The safe habit is to keep unknown devices off teaching laptops, keep a data-blocking policy for shared machines, and use a cheap sacrificial machine for the experiments in this guide.
Related guides
Try the full simulator with your class
103 guided circuit projects, 21 lessons and an in-browser Arduino simulator. The first 15 projects are free, no account needed. NCERT Science mapping on 47 projects, with Arabic and English copy in the regional builds.