An Arduino simulator that runs in your browser
ThinkEdge Learn is an Arduino simulator and circuit simulator that runs on the page you are reading — no install, no account for the first 15 projects, and nothing to plug in. Write a sketch, wire the circuit, press play, and watch the LED actually light.
Most people want to try one circuit before they buy a board. The Arduino simulator online is the fastest way to do that: open a project, drag the parts onto the board, and the sketch runs against the circuit.
The point of a simulator is not the drawing. It is the feedback. In ThinkEdge Learn the sketch is executed against a modified-nodal-analysis solver, so the numbers on screen are the numbers the circuit produces — current through a resistor, voltage at a pin, an LED that dims because the PWM duty cycle says so. Change the wiring and the reading changes with it.
That is why the simulator sits next to the curriculum rather than beside it. Every project on this site can be practised in the simulator first, and then built on a bench with the same wiring diagram, the same component list and the same code.
What you need to start
| What you can do in the simulator | What it shows you |
|---|---|
| Wire a circuit on a virtual breadboard | Every connection you make, with the pin and the net it lands on |
| Run a real Arduino sketch | digitalWrite, analogRead, analogWrite, tone, millis and the rest |
| Read a sensor | The live value — temperature, distance, light level, sound |
| Watch an output behave | LEDs lighting and dimming, buzzers sounding, servos sweeping |
| Break it on purpose | A missing ground, a resistor in the wrong place, a LED without a resistor |
Try these in the simulator first
Each of these opens in the browser simulator — no hardware, no download, no account for the first 15.
Switching a 50 mA lamp from a 20 mA pin
Use millis() instead of delay() — the right way to blink
analogWrite on D9 — the smoothest way to dim an LED
Press the button, hear a tone. The classic Arduino starter.
Read the room temperature every 2 seconds and print it
LDR + LED — the LED turns on automatically when it gets dark
5 LEDs that light up in sequence, like KITT from Knight Rider
The room gets dark, the LED turns on
Read the room temperature on your laptop
Sweep back and forth forever
Press A → go to 0°. Press B → go to 180°.
Walk past, the light turns on. Stand still, it goes off.
LED brightness follows the sound · quiet keeps it off
Detect motion with the PIR sensor and sound the buzzer
How the first internet worked — one click at a time
Four LEDs, sixteen numbers — counting in twos
Ultrasonic sensor detects when the bin is full
Three buttons, three options, instant democracy
How the simulator is different from a wiring diagram
A wiring diagram tells you where the wires go. A simulator tells you what happens after they do. Change an LED's resistor from 220 Ω to 10 Ω and a static diagram cannot tell you the current tripled; the solver can, and the LED on screen tells you what that current does.
It also makes the negative result teachable. A student can wire a potentiometer into an analog pin and watch the serial plotter draw the ramp, then pull the jumper out and watch it flatline. Those two failures are worth more than a working circuit, because the working circuit was never the thing that was hard.
How to use it with a class
Run the whole class on the simulator first, then book the bench for the physical build. The students who arrive at the bench already know what the circuit should do, so the session is about soldering and stiffness, not about debugging a wire for the first time.
The first 15 projects are free and need no account, so a class can start without anybody asking a parent to buy anything.
Common questions
Is the Arduino simulator free?
Yes — the first 15 projects run free and need no account. The simulator itself is what a school licence unlocks for the whole catalogue, and one licence covers every teacher on the roster and every student in their classes.
Does it need to be installed?
No. The simulator runs in the browser, so there is nothing to install on a school computer and nothing to update each term. You need a modern browser and a working internet connection to load the app.
Can I write my own Arduino code?
Yes. The lab has an Arduino code editor next to the circuit, with pin simulation, so you can change the sketch and watch the circuit respond. You can also open any project on this site and edit its code before you run it.
How is this different from Tinkercad or Wokwi?
Those are general-purpose circuit simulators — good at what they do. ThinkEdge Learn is a simulator built around a curriculum: the project you simulate is also a page with the concept explained, the parts listed, the wiring written out and the NCERT chapter it maps to. The simulation is one step of the lesson rather than the whole lesson.
Will a circuit that works here work on real hardware?
That is the point of the pairing. Each project page carries the same wiring and the same sketch that the simulator runs, so you build exactly what you practised. The simulator is honest about the things that differ — it models the parts, not the temperature of a classroom or a tired battery.
Related
Try the full simulator with your class
103 guided circuit projects, 21 lessons and an in-browser Arduino simulator. The first 15 projects are free, no account needed. One licence covers a whole school.